Download the Wizard, Frog, Viking and BONUS *Food Chain and Snake Spirit* cane patterns (PDF required) Realistic Skin Tones Types of paints By Lora S. Irish OIL PAINTS: I use oil paints when I need absolute control over blending color tones and when I want colors that are semi-transparent to transparent. Control: Since oil paint takes several days to dry, you have plenty of time to mix a new color on your palette and blend that color into one that you have already applied. I can apply a base coat of the skin tone in oils to the entire face. I can now add some white to the mix to make a highlighting color that I would use over the bridge of the nose, forehead, and along the tops of the cheek bones. Since they are oil paints, this new color does not go on as a brush stroke, but blends into the base skin color. I could add burnt umber to the base coat to darken it slightly and brush along the sides of the nose, in the eyelid areas, and along the jaw line. It will instantly blend to create shadows; lots of color but very few brush strokes. Application: Oil paints can also be used over a carving that has already been stained. You can stain the piece with burnt umber first, allow it to dry then add a coat of polyurethane spray. Then you can brush oil paints that have been thinned with a mixture of turpentine and linseed oil. You could also use stand oil or walnut oil. Linseed oil is commonly available and often used, but it develops a slightly yellow cast over time. Stand oil is a finer grade of artist's oils; it is thicker and allows the artist more working time. Walnut oil is a fine grade, absolutely clear oil that is easy to work with and never changes the coloring of the wood. Walnut oil and stand oil are available through art supply stores. This thinned oil color lets all of the stain show through, but gives a coloring over top. When oil paints are used directly over the wood, you will still be able to see some of the grain lines of the wood through the color. Clean up: For oil paint clean up, I use freezer paper as my palette. It's cheap and it's disposable! Plus, if I don't finish the painting in one day, I can pull off another piece and lay that right on top of the palette piece. This keeps the oils fresh until the next day, when I peel the two papers apart. Use a palette knife to pick up any paint from the top paper, put it back on the palette paper, and start into painting. So the only clean up I have is to wash the brush in turpentine. ACRYLIC PAINTS: Acrylic paints dry much faster than oil paints, so I use them when time is an issue, or when I want a semi-transparent or opaque finish. Control: The speed at which acrylic paints dry factors into the control you have. While you don't have as much time to blend acrylic paints into each other, there are a few mediums you can add to slow down the drying. Even with the addition of these mediums, the paints still dry faster than oil paints. When mixing colors, though, the best method is to mix the color and medium on the palette, and then apply to the carving. Application: The biggest advantage that acrylics have in painting is when you want an opaque effect; a strong, solid color, such as the red of Santa's coat. But in the past few years, acrylic paint pigments have evolved to the point that you can heavily thin the paint with flow medium or water for a semi-transparent effect similar to oil paints. I suggest you use flow medium for the craft-style paints, but you can use water for the artist quality acrylic paints. That allows you to see some of the grain, or add highlights to a piece you've already painted. If you don't like the effect, let it dry and paint again. It's easy to correct. Cleanup: Acrylic paints clean up with water when wet. If you accidentally allow the paint to dry, Windex with ammonia, or even straight household ammonia, work well to dissolve any paint left in the ferrule area of the brush. WATERCOLORS: Watercolors are finely ground pigment mixed in a water based float. Because the base float has no coloring of its own, the finished look of watercolors is extremely clear and crisp. This avoids the heavy look of thinned acrylics or oils. It's easy to get a transparent or semi-transparent coat with watercolors, but difficult to get an opaque coat. Control: Heavy thinning will aid you in controlling how much color goes on with each step. Thin the colors until the hues almost disappear on your palette. Application: Wait a few minutes between each coat for the previous coat to dry before you apply another coat. After you have finished building the colors you want, seal the carving with a light coat of polyurethane to set the color before you use any other painting or finishing method. Clean Up: Watercolors are easy to clean up with just water. If the paint dries in the ferrule area, soak it in a bit of water to loosen up the paint.

Discuss Realistic Skin Tones in our Forum

Having troubles opening the PDFs? Download and install the latest version of the FREE Acrobat Reader. To get it now click the logo on the right.