F200 duplicarver for sale,also a roto carver

dtoggs · #1 07-12-2007, 03:03 PM

I'm duplicarver poor,got two F200s and two roto carvers. I need to sell and buy a router table lift and other tools. Anyone interested? Yep,shipping is costly,but this is about as inexpensive hobby you can get-lots cheaper than fishing or hunting. Don't want to buy? We'll just talk then. I'm retired and have the time.

sbirkes · #2 09-20-2007, 08:47 AM

Did you sell your Dupli Carver?

Hi_Ho_Sliver · #3 09-20-2007, 07:42 PM

Got any pictures of sites that show them? Guess we are both a little slow reading these huh Steve LOL

dtoggs · #4 09-20-2007, 07:48 PM

Yes,go to www. terrco.com for duplicarver pictures or see pm for my emailer and I will show you the pictures of all my units. pw

Wolf Kiessling · #5 09-20-2007, 11:29 PM

Quote:

Originally Posted by dtoggs

I'm duplicarver poor,got two F200s and two roto carvers. I need to sell and buy a router table lift and other tools. Anyone interested? Yep,shipping is costly,but this is about as inexpensive hobby you can get-lots cheaper than fishing or hunting. Don't want to buy? We'll just talk then. I'm retired and have the time.

I'm gonna be selling my duplicarver pretty soon and, if you don't mind, I'd like to get a little info from you. When/if you find a buyer that is out of your area, and you plan to ship it, are you going to disassemble the unit (the way Terrco ships them) or are you planning on shipping it intact. If you are going to ship it intact, where do you find a box big enough to pack it in? Do you plan on shipping it UPS?

dtoggs · #6 09-21-2007, 06:00 AM

Good morning Wolf,to answer your question about shipping,I think palletizing and shipping by truck would be my only option. I would dissassemble the machine as it breaks down easily,but is much too cumbersome to leave assembled. I also have a delima,what to do with the spindle set. The rails are 6'long and that creates a problem. I picked it up with my Tacoma from previous owner.

I still have my machines,shipping costs has always been the deal breaker,but unless its picked up,what other way is there? NO,I WON'T DELIVER! ha ha Paul

Low_Bridge · #7 10-09-2007, 02:13 PM

What are you getting the F200 & What's the ship to Florida?

dtoggs · #8 10-09-2007, 06:46 PM

Hi Low Bridges. I'm asking 625$ for the duplicarver and spindle set. I can give you dimensions that Terrco gave me: 32''x38''x16'' 225lbs for duplicarver,for F200A spindle set: 8''x 76''x16'' 65lbs. Counter wt: 50lbs,approximately 3'x4''. You can ck the truck lines in your area. I will palletize and tie down,no extra charge. If you will send me a pm,I will give you my email address and can send a picture. 1 1/2 pc router included-never used,comes with instructions and is fully supported by terrco. Current price from terrco is 1310$ on duplicarver and 260$ for spindle set. Yeah,the trucking is expensive weather you buy from me,the factory or some one else. Regards,pw.

Low_Bridge · #9 10-13-2007, 04:34 PM

Well I bit the bullet& went with the T-110, I found a new / unused model- With all options & burs

dToggs was extremely helpful in providing me with information on his machine-

For a beginner & a new project I decided to start out one step at a time-

Insured shipping to Florida was going to be about 280- so even at that dtoggs still comes in at less than half of a new one- So it looks like someone will get a good deal with dToggs' machine
Thanks all for your help!!

sbirkes · #10 11-02-2007, 12:40 PM

Paul, I just sent you an email. I'm trying to figure a way for me to buy your duplicator.