Drawknives

Captain_Bandaid · #1 05-04-2003, 02:35 PM

How many of you out there use a drawknife to rough out a carving? As many of you already know, I also enjoy Blacksmithing when I am not carving. Just for grins, I cut one turn off of a large railroad car spring and forged it into a draw knife. Hardened it to Rc 57 at work and today I ground the edge on it. To my astonishment, it worked extremely well! I am amazed at how this simple tool can precisely rough out a carving almost as fast as a band saw! The one I made has a blade that is 3/4' wide and about 5' long. The handles look like a handlebar mustache with no wood grips. It is all iron but extremely controlable. If you haven't already tried a drawknife, you might find it very useful.

AlArchie · #2 05-04-2003, 03:52 PM

I've been using a drawknife for about 8 years. First a large one (10') and just recently picked up a 5' one from Lee Valley.They can really trim down the time used in roughing out carvings.

Al

#3 05-04-2003, 05:17 PM

I'd never thought of using it on carvings ... use it a lot roughting out bows ... guess I'll have to sharpen her up and give it a go. Thanks for the idea.

Colin_Partridge · #4 05-04-2003, 09:15 PM

Hi Gang,
I purchased a draw knife from Flexcut a beautiful little tool. This one is like their other tools in that it does flex and it is extreamly sharp just like a straight razor. It is also very small and light I wouldnt be with out mine. I have three of them the other two are larger and heavy duty but on large carving they are the cats behind.

Colin

#5 05-05-2003, 02:49 AM

Hi

I have in mind to buy a Drawknive for my roughing out works.
I need one.
Have you any recommendation to buy?

Flexcut, PFEIL, Other....

Saturno.

#6 05-05-2003, 04:00 AM

A friend uses one a lot for fish. Since you mentioned black smith work another friend said his old group made tools from lawn mower blades by annealing them in a log fire. Hack saw out the shape then re-tempering it. Any thoughts on this? Thanks.

AlArchie · #7 05-05-2003, 06:37 AM

Bob, I use mine mostly for fish, too, but also for removing bark from small logs. that dulls them pretty fast, though, so I keep one specifically for 'debarking'. They seem to offer a lot of control for roughing and at the same time remove stock quickly.

For Saturno, I'd bet the Flexcut is a fine tool, but small. A Larger one, either straight or curved can be found at www.lehmans.com, under the tool section. I picked up a real beauty of a small drawknife from www.leevalley.com This one is NOT flexible, but it is razor sharp, and a dream to work with. . It's about 3/16' thick (about 5 or 6 mm), and 6' long (5' cutting edge) that's 125mm with 120 mm cutting edge, I think, if my conversions are correct!

Al

Al

#8 05-05-2003, 07:52 AM

Al, You say a drawknife for removing bark and another for nomal roughout, but at this time I have only money for one drawknife. :-/

I can get a PFEIL drawknife for 30$ here in Spain, cheaper than 45$ in Woodcraft.com

(A) Straight Drawknife. Blade 5' long x 7/8' wide, overall length 12-1/2'.
(B) Carver's Drawknife. Blade 4-1/2' long x 7/8' wide.

Is these drawknifes a good choice for roughout and also for 'debarking'?

Thanks
Saturno.

noel58 · #9 05-05-2003, 09:04 AM

I too love blacksmithing, and enjoy making my own tools.
Its a great high to carve somthing from a block of wood, but to carve it from a tool you made yourself is a high only a few of us really know. The draw knives I make come from old files and springs from the flea market. All of my hardening is done by the seat of my pants. Most people don't know the toil and trouble to forge such a piece. People only want to pay $5 to $10 bucks for your tools, it really hurts. Kind of like having vise grips pop open in your pocket!!! :

AlArchie · #10 05-05-2003, 09:44 AM

Saturno, that lower picture of the drawknife on your last post looks to be the same one that Lee Valley markets for 42 US dollars. I'd get that one in Spain if available for the $30 price. It is a very fine carving tool, and I would not use it for debarking.

Might I suggest you try to grind your own drawblade from an old lawn mower blade? For debarking purposes you don't need a real good blade; just make the handles comfortable. You should be able to pick a new lawn mower blade up for a few dollars in any decent hardware or implement store.

Al